The Frontier Sixshooter Community Message Board - Primer "detonation" in a Dillon primer tube?

Primer "detonation" in a Dillon primer tube? (reply)

LAH — Tue, 02 Oct 2012 18:47:47 +0000

I've set a few off but never in one of my Dillons.

I have four 550s and one 1050. In total, far over 100K (reply)

Alfred John — Mon, 01 Oct 2012 14:04:49 +0000

Amen on taking care of the equipment. I have used mainly a single stage press and enjoy doing so. On a progressive when I use it, I will stop about every thousand rounds, take a break, clean everything in and on it. Look it over and make sure everything is within spec. This prevents a lot of problems from cropping up. Todays progressives properly served should not wear out. A lot of beginners get spoiled and want to rush on this stuff. It doesn't pay. Just my take. Good Luck......

That's the revolver race gun secret... (reply)

cas — Mon, 01 Oct 2012 00:42:17 +0000

…really deep seated Federal primers and super light double actions. Personally I can't be bothered.

Yes sir.. Federals seem to have the softest cups and are the most sensitive. (CCI would be on the other end of the scale, though the Wolfs could be worse)

What do federal primers have to do with it? I saw that (reply)

John K. — Sun, 30 Sep 2012 22:22:02 +0000

being easier to ignite.

Lots of custom gunsmiths used to back off of the springs a lot to give a nice trigger pull and then specify Federal primers. Real Cute.

What do federal primers have to do with it? I saw that (reply)

Mark — Sun, 30 Sep 2012 22:16:55 +0000

in a post there as well. How are they different?
Mark

Tim Sundles uses 1050s, right? Has he ever had such? (reply)

Hobie — Sun, 30 Sep 2012 21:30:24 +0000

You could ask him...

I have four 550s and one 1050. In total, far over 100K (reply)

John K. — Sun, 30 Sep 2012 21:04:01 +0000

rounds through them without a detonation.

However, ANY bulk accumulation of primers is subject to detonate with sufficient jarring or force. That's why the primer manufacturers package them in the fancy cartons.

I've seen pics on the internet of sheetrock ceilings shredded by a tube detonation.

Dirty, maladjusted equipment and operators poking at stuck primers are the usual suspects. Dust from priming compound is usually blamed as that sounds a lot cooler than admiting to simpler explanations.

Having watched mechanically inept reloaders on the internet buying go-fast progressives, I'm now convinced most should have to take a test before being allowed to buy one.

How long's the L&L been on the market? (reply)

cas — Sun, 30 Sep 2012 20:45:51 +0000

I'm 43 and I've had my first 550 since I was a sophomore in High School. That would lead me to believe there's a lot more Dillion's out there, so odds are in their favor to hear more about them.

Usually it's the 650 you hear about. The way the primer system in that one is if you crush one while seating it, it and start a chain reaction and blow out the the whole tube. I've seen a few pictures of 650's that have shot the primer rod up into the overhead. That's why I don't use Federal primers in mine.

I have 4 dillon machines have loaded thousands of rounds (reply)

Rob Leahy — Sun, 30 Sep 2012 20:43:16 +0000

pay attention to the forums and have never heard of this??? I suspect someone f'd up and uses a sharp tool on a soft primer.

Primer dust (reply)

Dennis — Sun, 30 Sep 2012 20:39:03 +0000

Just wondering is there something or some reason why you never see or hear of this happening in other progressives such as the Hornady LNL. I would think that if it is a primer dust problem there must be extenuating circumstances as to why it only happens in the Dillon. And until further investigation reveals a concrete reason all the more reason to spend less money and get the Hornady. But then you may have guessed I already own the Hornady ;>). Dennis

Primer dust (reply)

Fivegunner — Sun, 30 Sep 2012 16:54:29 +0000

you got to keep your reloader clean of the build up of primer dust, that`s what I think

Primer "detonation" in a Dillon primer tube? (reply)

Alfred John — Sun, 30 Sep 2012 15:15:47 +0000

I have heard of it and seen an article some years back on it. If you do a high volumn of reloading it is probably possible. Primer "dust" can build up a bit and it wouldn't take much to set it off. I used to reload a lot of .38 specials and because of this worry I would clean the primer tubes before and during the reloading. Of course I would load several thousand at a time using multiple tubes. I do believe it is possible. Just my thoughts.

Primer "detonation" in a Dillon primer tube? (reply)

Dave B — Sun, 30 Sep 2012 15:10:06 +0000

I have been loading on my RL550B since 1994 with nary an issue. I am not sure I can see how this could happen short of a primer getting stuck inside a tube and used something metallic to try and force it out.

Primer "detonation" in a Dillon primer tube?

Mark — Sun, 30 Sep 2012 13:05:21 +0000

Did anyone else read this over at the Cast Boolits website: http://castboolits.gunloads.com/showthread.php?t=166612 ? This fellow says that there is no obvious cause. Another person writes that it has happened to him a few times. I have never had anything close to this happen when I use my Dillon 550. I am thinking there is more to the story but I bring this up here because I want to know if anyone here has a similar story.
Mark